This section has hundreds of instructional videos showing how to do the easiest of DIY related jobs right up to a full bathroom refurbishment. If you cannot find the video you are looking for please use the search box. In this video I install some UPVC quadrant beading to a shower tray. This is often the only solution to get a waterproof seal, if the gap between the tiles and the shower tray is too large. This can also be done to the side of a bath, if there is a large gap. This is the second video in the series, how to clean the old silicone off and re-apply new silicone can be seen in this video- https://youtu.be/6o5JVxvWuhQ We know that not everyone has the luxury of a freestanding bath and that many modern bathroom designs will incorporate over-bath showers that also require sealing. When sealing a bath, follow the preparation advice above but remember that there is one crucial extra step you will need to take before reaching for the silicone sealant.

Buy a hygienic silicone sealant of good quality. It should specify that it is suitable for use in bathrooms / wetrooms and contain an anti-mould and bacterial additives such as Kerakoll Fugabella Eco Silicone Sealant or Kerakoll Fugabella AM Silicone Sealant, which are both available from our sister company UK Tiles Direct. Choose the correct type of silicone sealant that is compatible with your chosen wall or floor coverings (such as natural stone, porcelain tiles or ceramic tiles). Consult the tile supplier or sealant manufacturer for further guidance.Whether you are resealing the shower enclosure in the bathroom at home or you are a contractor planning on sealing showers for a large development, the best advice we can give you is: Starting from the point the silicone was first applied, place the silicone sealant smoothing tool against the shower tray and tiles. Apply gentle but even pressure and draw the tool along the length of the shower tray, remove excess silicone and leave a neat bead as you go. Wondering how to seal a shower tray or looking for top DIY tips on how best to apply silicone sealant? Room H2O’s expert advisors are here to help … Room H2O appreciates that DIY is not everyone’s cup of tea and there are some jobs you would rather leave to the professionals. With that in mind, we offer a full range of specialist services from bathroom installation services in Dorset to made to measure shower enclosure survey and installation services throughout the South East. Should you require more information about our shower sealing and bathroom fitting services, do not hesitate to get in touch. Make it neat – A sealant application tool, such as the Fugi by Cramer, will help you to achieve a neat and even bead of silicone sealant

Buy a good retractable utility knife. A sharp knife will be required for opening the silicone sealant and trimming the application nozzle to size. Do not apply too much sealant as excessive amounts can be difficult and messy to remove. More sealant can be applied prior to smoothing if required 6 – Make sure there are no gaps in the sealant bead The nozzle of the silicone sealant tube will usually feature perforated marks to indicate where and how to trim the nozzle but a good rule of thumb is to cut at a 45-degree angle and create a 5-6mm hole in the end of the tube, which can be enlarged if a wider bead is required.Apply the silicone sealant to the inner corner of the shower tray. Use gentle pressure to the trigger of the application gun and work towards the front of the shower tray in one continuous, smooth action to ensure application of a uniform silicone bead. Seal that shower – Follow our shower tray sealing tips above for hassle-free shower sealing with a smooth, neat finish. Once a smooth, uniform bead has been achieved around the shower tray, do not be tempted to keep smoothing the silicone as it will start to tear, look untidy and may not adhere correctly. 10 – Allow the silicone sealant to dry fully

One of the most common causes of water leaks from shower trays, shower enclosures and baths is the poor application of silicone sealant. Here are some handy tips to set you on the right path and make sure you apply silicone sealant correctly to achieve a professional finish and prevent water leaks. Shower tray sealing: the right tools If using a tool to smooth the silicone sealant, select the correct aperture size to produce a bead that will fully cover the gap between the shower tray and tiles. Allow to cure fully according to the manufacturer’s instructions. Usually, fresh silicone should be left to dry or cure for a minimum of 24 hours, although this depends on the brand and type of sealant.Thoroughly dry the shower tray area with paper towel or allow the shower tray to air dry for a couple of hours before applying the silicone sealant, which will not adhere properly should any moisture remain. Give the area a final wipe down with a clean damp cloth to remove any residual detergent but do not get the area wet.