LIGHTAILING Light Set For (Ghostbusters Ecto-1) Building Blocks Model - Led Light kit Compatible With Lego 21108(NOT Included The Model)

Product Information

Follow LeLightGo step-by-step instruction to light up your Ghostbusters ECTO-1, something amazing will happen at night. All our kits are plug and play - no electronics knowledge needed! Take the front grey pole with attached lights and disassemble all the pieces as we will be replacing the grey pieces with new pieces (with different clips). The Modular Building series is a dream come true for adult fans of LEGO®. With ultra-detailed buildings, ranging from a Town Hall (10224) to a Detective's Office (10246), there is enough variety in sets to create your own large scale LEGO® town. And now with our easy to install light kits, you can create your very own realistic and fully functioning town. LEGO® Technic This kit has not one, but two sound modules, and together these modules can play four sounds at the same time. This provides the most realistic sound possible, including: Genuine LEGO® Parts for the Movie-Accurate Replacement Roof Strobe, Motor, and to Hold Adapters and Controllers in Place

This LEGO light up kit contains lighting features such as flashing sirens on the top of the Ecto-1, front and rear headlights, and flashing emergency lights at the rear of Ecto-1. Installation Guide

If you want to control the lights and get a special sound kit, then it's best to get the Standard RC + Sound Version. However, both Standard RC + Sound, Standard Remote and Standard versions are a wonder to behold at the same time as they come with the same lights. ABOUT INSTALLATION Before dive into the KIT itself I have to remark, that the customer service was just fantastic before buying the KIT. I had some doubts and questions but they were just provided one of the best support online. Remove the front section with the grill and number plate attached, followed by the 2 Lego 2×4 plates with light pieces attached.

The LEGO Ghostbusters Ecto 1 (21108) is a faithful recreation of the iconic vehicle from the hit 80s movie franchise, Ghostbusters! Reconnect the transparent blue triangular plates we removed earlier on top of the additional plates we just installed. Locate 2 of the provided grey plates with clips as we will be replacing the original ones with these. Take another 2 flashing Bit Lights and install them by placing them over the studs and connecting the blue transparent round pieces over the top. It’s time to neaten up all the cabling from the LEDs we have installed so far. Take the 5 cables from the front lights and twist/wind them around each other starting from the base working your way up. They should all come together neatly.Take the 2 provided Lego 1×6 white pieces and connect them underneath the roof securing the front and middle roof sections together. Take 1 standard Bit Light (non flashing) and place it on top of the stud of the grey round plate ensuring the LED component part is facing the correct way up. Secure the LED in place by connecting the transparent Lego plate over the top. Authentic Cadillac ambulance engine sound that loops until you stop it. Includes unique start and stop sounds, and even a great"engine stall" sound that will be triggered 40% of the time when you start the engine.

If there's something strange in your neighbourhood, who are you gonna call? Why the Ghostbusters of course! Take one of the provided grey Lego pieces with clip and place 1 standard Bit Light (non flashing) on top of the stud. Secure the LED in place by connecting the transparent red round piece over the top ensuring that the LED component part is facing the correct way up. Ensure the cable from the LED is facing the same way the clip underneath is facingTo ensure a trouble-free installation of your light kit, please read and follow each step carefully. Ever wanted to create your own LEGO® set? That's exactly what LEGO® Ideas is! Fan-submitted creations have now been turned into actual commercially available sets! Turn the roof on its side to allow you to then group all the cables from the front roof LEDs. Twist/wind them around each other, same way we did for the rest of the light cables. Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do not force it. Take the cable from the LED we just installed and the 2 cables from the front right lights and hide them in between studs up the right side of the car by reconnecting the grey triangular plates over the top of them.