INSTALLATION NOTE: This film has a horizontal, inherent, very fine pattern repeat line across the width of the roll which repeats every 495mm. The material should be sealed in place, you can then with your Green Card Squeegee, and Snap off Knife, trim the film to the shape of the window. Feathered Pattern translucent embossed vinyl film. Clear Etched feathered pattern. Translucent embossed vinyl film. Suitable for internal and external applications. Lustalux LTD recently completed a large scale installation of reeded window film to an office at the Media City in Manchester. Commercial Partner or Home DIY We put the reeded film on our bathroom window and we really like how it looks especially during the day when its sunny. Our bathroom glass already had a slight blur effect to it but we didn’t like the pattern. This reeded pattern goes on top well and really modernises the space.

Place the Green Card Squeegee on the film and against the edge of the glass, then place the blade of your knife against this. This will guide your knife and protect your window frames and gaskets. Note: Making a diagonal cut between the corner of the glass and excess film prevents creasing the corner of the material while trimming. This film simulates real reeded glass. Bands are 13mm wide and band direction is vertical, down the length of the roll. Wetting solution is the secret ingredient to a smooth, seamless installation. Make a solution by adding 8-10 drops of a mild, non-moisturizing dish detergent (Dawn or Joy; do not use hand soap) to a 32-oz. spray bottle filled with clean water (adjust ratio for smaller or larger bottles). More soap may be needed when applying film to acrylic surfaces. If you have hard water, consider using filtered or bottled water, to prevent mineral deposits under the film. Mix well. Tools: Scissors, Tape Measure, Razor Knife, Ruler, Plastic Card Squeegee, Spray Bottle, and Paper Towel.Give yourself enough space to work. You will need enough flat surface to lay out the film for measuring, cutting, marking and prep. Do not run a fan near the film or glass surface during installation. This can cause dust and debris to blow onto your film and become trapped. Steps Water bubbles are a factor in window filming that can not be avoided. Depending on the tools and pressure applied, you may remove up to 95% of the application fluid. The remaining 5% due to surface tension will form small bubbles and if left alone, will completely dry. This process normally takes no longer than 30 days but can take up to 60 days depending on the quality of installation. With the exception of films specifically labeled and made for exterior application, always install film on the interior of a window. Film applied to the exterior will easily fail due to exposure to the elements. After the film has been applied, dry every edge and the surface with a paper towel. Be thorough and careful, especially in the corners. Make sure all the water, or as much as possible, has been removed from behind the film.

Translucent embossed vinyl film. Ideal for obscuring direct visibility and allows excellent light transmission. Finer brush than SXHE-02. Suitable for internal and external applications.

The Film:

Processed ( toughened and non toughened, polished edges, holes, radius corners etc) - 10-15 working days

Unit 10 The Edge, Humber Road, London NW2 6EW | Registered in England and Wales No: 4770280 | GB 832946508 If you notice small bubbles that start to appear after all the water seemed to have gone, this is perfectly natural and part of a ‘curing process’. Please note all doors (External & Internal) & any window that isa within300mmof any dooror within 800mm of the finished floor level must be toughened or safety glass. Our ‘SX-’ coded textured window films, also known as Solyx, covers our most extensive range of any of our product categories. Some of the textures that can be achieved within Solyx include antique mirror glass, coloured glass, cotton, etched glass, frosted glass, mosaic and reeded glass. However, you’ll also find plenty of window films with special effects that can create a dazzling colourful spectacle for your window glass too. There are unlimited designs to explore for commercial window films including general glass, window glass, mirror glass and even wall coverings. A very small clear borer should be visible between the edge of the film and the frame. This is normal and is integral to the installation process as it allows the removal of the water.SX-1730 Rhombus is a clear translucent/transparent, high grade embossed film. This product is ideal for obscuring direct visibility while allowing excellent light transmission.