AirCube ISP

Product Information

To reset a Ubiquiti ISP wireless device (ex. airMAX, airFiber, LTU) to factory defaults via SSH / CLI, log into the unit, and run the following as one command:

Ubiquiti Dual-Band 802.11ac Wi-Fi Access Point with PoE In/Out - Ubiquiti

If no DHCP server is present or an IP cannot be obtained via DHCP, the radio will revert to 192.168.1.20By reloading fresh firmware to restore the device, this process can also be useful to recover devices that have appeared to fail when no other solution is working.

ACB-AC Quick Start Guide - Ubiquiti

The Ubiquiti airCube airMAX AC Home Wi-Fi Access Point ACB-AC is a Wi-Fi access point for use in your residential customer deployments.The Ubiquiti airCube AC features 4 x Gigabit Ethernet Ports, 24V PoE Passthrough for airMAX CPE and Dual-Band, 802.11ac, 2x2 MIMO Technology. Warning: Do not switch off,reboot ordisconnect the device from the power supply during the firmware upgrade process, as these actions will damage the device. Resets to factory defaults. The device should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the LED starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the device will automatically reboot.Since the customer also wanted to have the WiFi in the shed, I also needed to buy a Wireless Access Point. I noticed that Ubiquiti recently released two basic access points, Aircube ISP and Aircube AC. The former is cheaperbut supports only 10/100 and 802.11n. It’s still a relatively good option for budget oriented builds and certainly better than many ISP routers. This article describes how to enable & configure port forwarding on ISP Wireless devices, as well as steps to test & troubleshoot that port forwarding was successfully set up. The instructions in this guide assume that your device is already configured with an active Internet connection.

Ubiquiti Networks airCube ISP Wi-Fi Access Point (ACB-ISP-US) Ubiquiti Networks airCube ISP Wi-Fi Access Point (ACB-ISP-US)

Please Note: This product does not come with a UK Cable. If required, please select PoE kit from the dropdown above. Test your Work.Once all Port Forwards have been added and applied, you can test from outside your LAN.In this example, you would try to access https://203.0.113.48:8443 from another connection to verify the port forwarding was set successfully. Troubleshooting Optional) If you would like to restrict access to the port forward, you can also add a Source IP/CIDR subnet mask. For example, adding 192.0.2.1/32 to Source IP/Mask would allow only 192.0.2.1/32 to access the Port Forward. Aircube can be configured as either AP or repeater. Every major configuration change results in having to restart the device. For this customer, AP is what I need as it will be connected to a wireless P2P link. Repeater is useful for situations where you want to connect to a router further away and place your own access point in the middle. Generic Linux distributions have an integrated command line TFTP client. From a PC running Linux, you can upload via TFTP by typing into Terminal the following commands: root@ubuntu: tftp 192.168.1.20

Ubiquiti Inc. (UI) Products

The innovative antenna provides wide-area coverage, and the airCube’s elegant design allows you to place it anywhere. The Ubiquiti airCube airMAX ISP Home Wi-Fi Access Point ACB-ISPis a Wi-Fi access point for use in your residential customer deployments.The Ubiquiti airCube AC features 4 x 10/100 Fast Ethernet Ports, 24V PoE Passthrough for airMAX CPE and 802.11n, 2x2 MIMO Technology. The airCube's attractive design means it can be positioned anywhere in the room, improving Wi-Fi performance. Signal LEDs will keep blinking one by one in 4 different colors during firmware upgrade. Wait for about 7-10 minutes (devices and firmware depending). Remember to not power off the device during the procedure.

to setup airCube AC Home Wi-Fi Access Point l Ubiquiti How to setup airCube AC Home Wi-Fi Access Point l Ubiquiti

Note: The device being Port Forwarded to should either have a static IP (with a router as default gateway) or a DHCP Lease Reservation. If not, your Port Forward may stop working on a router or device reboot. Steps: How to Port Forward on airCube For airCubes (ISP and AC): Push reset button and hold while powering unit.LED panel should blink fast several times, continue holding the reset button and the LED should turn off. Now you can release the reset button and the LED will flash slowly three times.

Ubiquiti ACB-AC WiFi 5Access Point (AC)

Verify that the device has the correct default gateway/subnet if configured with a static IP. The gateway should be the airRouter IP in this example.